Pendle Cycle Carriers

TA4 Pendle Towbar Mounted 4 Bike Carrier suitable for most flange ball towbars
Suits vehicles without a spare wheel mounted on the rear.


Can be used whilst towing but we recommend restricting the number of bikes to two due to the possibility of fouling the caravan or trailer when on full turning circle.
Comes with single electrical mounting plate.
Check towbar nose weight when towing & cycle carrying at the same time.
Application Guide

TA4H Pendle Towbar Mounted 4 Bike Carrier suitable for most flange ball towbars including type approved bars.

This version is 15" higher than the TA4 which overcomes problems of fouling the drawbar when towing and carrying bikes at the same time.

Important:- Noseweight limits must be observed.
This is the total weight of the bikes & carrier and the noseweight of the trailer/caravan added together.
Turning circle should also be checked to ensure no contact between the bikes and drawbar is possible.



Application Guide

A 4 bike cycle carrier that fits on the towball. Obviously it is not possible to tow whilst using the rack. The rack is the same style as the TA4 but clamps around the towball. This is particularly designed to suit the swan neck style of towbar where other racks are impossible to fit.


Application Guide

This four cycle rack is designed to fit on Land Rover Discoveries & similar vehicles where the spare wheel is mounted on the rear door.
It can be used when towing but as with the standard rack, be aware of the turning angle of the caravan or trailer.

Comes with single electrical mounting plate.
Check towbar nose weight when towing & cycle carrying at the same time.
Application Guide

As TAD but this is version is 15" higher which overcomes problems of fouling the drawbar when towing and carrying bikes at the same time.


Important:- Noseweight limits must be observed. This is the total weight of the bikes & carrier and the noseweight of the trailer/caravan added together. Turning circle should also be checked to ensure no contact between the bikes and drawbar is possible.
Comes with single electrical mounting plate.

Application Guide

As TBM4 Rack above but for use on Landrover Discovery and vehicles with rear door mounted spare wheel requiring clearance of approx. 110mm.
Application Guide

Like the TAD Rack, the TAL version has been designed to fit 4x4s with spare tyres on the back and the rack arms are offset by 10 inches in order to ensure that the bike rack fits those vehicles with wider spare tyres.
Due to the rack allowing up to 10 inches offset, It is not advisable to tow and transport bikes on the Landrover rack at the same time as the rack would interfere with your turning circle.
Comes with single electrical mounting plate.

Application List

As the TAL rack but with clamp around the ball type mounting to suit swan neck and detachable towbars. Will also fit flange ball towbars. It is not possible to tow and use the rack at the same time

Comes with single electrical mounting plate.

Application List

2 Bike Carrier that straps on the door mounted spare wheel on 4WD vehicles. Spare wheel cover cannot be replaced whilst rack is fitted.

Pendle 2 Bike carrier that bolts to the centre of the door mounted spare wheel on 4WD vehicles. Has a variety of mounting holes to suit most vehicles.

There are four mounting plate versions: A, B, C, & D
Please refer to the vehicle appliocation guide and check the appropriate box for your vehicle.
If in doubt please contact us before purchasing and we will be happy to assist you.


Vehicle Application Guide

The Wheel Support Rack is one of the most versatile bike racks in the Pendle Bike Racks range. It will fit almost every vehicle with a flange ball tow bar fitted subject to nose weight limits. The bicycle wheels are supported by D-loops attached to the main frame of the rack and each bike is held separately in its own support. Individual vertical arms separate the bicycles from each other in order to ensure non-contact between bikes during transit. You cannot tow with this particular rack because of its platform style design.
The Wheel Support Rack is supplied with a lighting unit.

Can be used on swan neck and detachable towbars with the clam shell adaptor
Please observe towbar noseweight limits. The rack weighs 18.5kg
Vehicle Application List

Pendle Car Plate for flange ball towbars.
Suits TA4, TAD, & TAL racks

Pendle Car Plate for swan neck and detachable style towbars.
Suits TBM4, TBMD, & TBML racks.

Pendle Single Mounting Plate for 7 pin socket for use with towbar mounted Pendle racks TA4, TAL, & TAD

Pendle Double Mounting Plate for 7 pin sockets for use with towbar mounted Pendle racks TA4, TAL, & TAD

Long R Clip for Pendle TA4, TAD, & TAL Cycle Carrier Car Plate.

The Clam Shell Adaptor allows you to use your existing Witter, Pendle or any other flange ball type cycle carrier with a swan neck or detachable ball towbar. Very quick and easy to use. It takes less than a minute to attach with a 19mm spanner. Very secure once tightened.
Please note: it can't be used whilst towing.
Requires 2 x M16 bolts - can be purchased as an optional extra - please check the box

This 3 ft light board is designed to be used with cycle carriers only. It has a short lead and the legally required reflectors which do differ from those required on trailers and caravans. Please be aware that it is illegal to obscure the lights and number plate on a road going vehicle and it is therefore likely that a light board will be required if using a cycle carrier. Penalties for non compliance are high.

A new board to our range. This one is yellow, 4ft wide and has 2m cable

This light board has 2m cable and is 4'6" wide making it particularly suitable for larger vehicles carrying cycles.It also has a fog light.

A pair of quick release number plate mountings.
Allows the use of different number plates quickly & easily without tools.
Will fit on any flat surface.
Stainless steel

Number plate holder
Allows the use of different number plates quickly & easily without tools.
Will fit on any standard plastic light board or over timber up to 3/4"/20mm thick
White powder coated steel